Exactly How to Remove and Also Change a Bathtub
Exactly How to Remove and Also Change a Bathtub
Blog Article
This great article below on the subject of A Step-by-Step Guide to Installing a Bathtub is truly informative. Check it out yourself and figure out what you think of it.
Setting up a tub isn't exactly rocket science, but it does require solid plumbing, carpentry, and in some cases, tiling skills. Replacing an old bathtub with a new one is also a moderately difficult project. If the old tub is readily accessible, the project can move immediately; if you need to open up a wall surface to eliminate the old tub and position the new bathtub, the job is a lot harder. In either instance, the job is within a house handyman's skills, although you will need a helper to vacate the old bathtub and also embeded in the new one. Ensure you have qualified on your own for the work as well as are comfortable attempting it. Rather than hiring a contractor to take control of a halfway-completed job, it is much better to consider using one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This article will certainly aid you set up a new bath tub in your washroom if you have already acquired a new tub and also don't require to alter the arrangement of your previous water system pipes.
Your devices as well as material list should consist of the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, after that the first thing you ought to do is separate the water supply. After doing so, switch on the faucets to drain any type of water remaining in the system. The process of getting rid of the existing taps can be rather bothersome due to the limited gain access to that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a towel ready for the remaining water that will certainly originate from the pipelines. As soon as the supply pipes have actually been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Prior to proceeding to fit the brand-new faucets, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the other end offers a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin making sure that the washing machines remain in location in between the faucet as well as the sink. Protect the faucet in place with the manufacturer offered backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular tap connectors. The previous kind needs to be attached to the faucet finishes initially, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Tub
Using the two wooden boards under its feet, position the bath tub in the needed setting. The wooden boards are useful in evenly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto four small factors.
The following objective is to guarantee that the bathtub is leveled all round. This can be achieved by examining the level as well as changing the feet on the bath tub up until the spirit level reads degree.
To set up taps, fit the bottom of the outermost versatile tap connector to the ideal supply pipeline by making a compression join; then do the exact same for the other faucet.
Turn on the supply of water and also examine all joints as well as new pipework for leakages as well as tighten them if necessary. Load the tub and additionally inspect the overflow outlet and also the typical outlet for leakages.
Lastly, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub ought to wait till the bath tub has been made use of a minimum of once as this will certainly settle it right into its final placement.
Getting ready for the Installment
First of all, the supporting framework supplied with the bathroom ought to be fitted (if needed) according to the supplier's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps device to prevent stress on the bathtub.
Fit the versatile faucet ports to the bottom of both taps utilizing 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath should now be ready to be suited its last placement.
Tiling Around the Bath tub
In the area where the bath meets the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to break a stiff seal, triggering the water to pass through the wall surface in between the bathroom and also the tiling, bring about difficulties with moisture and possible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your fixtures and fittings. They are offered in tubes as well as cartridges, as well as can securing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to allow for the movement experienced when the tub is in use. The sealant can crack fairly early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate reading up on How to Install a Bathtub Yourself? Try leaving feedback below. We would be glad to see your feelings about this review. We are looking forward that you come back again in the near future. So long as you enjoyed our post kindly remember to share it. Thank you for your time invested reading it.
Go Company
Report this page